Mini Slide hammer

• Sharp Side Panel Hook 1'' Curve Flag
• Sharp Side Panel Hook 2 1-1/2'' Curve Flag
• Sharp Side Panel Hook 3 2'' Curve Flag
• Sharp Side Panel Hook 4 2-1/2'' Curve Flag
• Sharp Side Panel Hook 5 3'' Curve Flag
• Sharp Side Panel Hook 6 3'' Curve Flag

Side Panel Hook Set 

The Side Panel Hook Set is a set we recommend for every technician. It can easily be part of your foundation of tools used daily.

Length's & Flags:

• 2 x 8'' (20cm) with 1'' and 1-1/2'' flags
• 1 x 12'' (30cm) with 2'' flag
• 2 x 18'' (45cm) with 2-1/2'' and 3-1/2'' ball end flag
• 1 x 24'' (60cm) with 3'' curve flag
• 1 x 30'' (75cm) with with 3-1/2 curve flag 

Diameters:

• 2 x 3/16'' (4.7mm)
• 2 x 1/4'' (6.3mm)
• 1 x 5/16'' (7.9mm)
• 2 x 3/8'' (9.5mm)

1-1/8'' whale tail tip
3'' length of tool

28.5 mm whale tail tip
76 mm length of tool

Length: 20”/ 50.8cm

Thickness of Shaft: .125" / 3.17mm

Width of shaft: .250”/ 6.350mm

Tip width: 3/4”/ 2.8cm

Gang Green Dead Center Tabs are the new kings for Hail Repair!

The dead center tabs have shown us that the most effective way to move metal is to flex with the metal as the repair is performed.

Using that knowledge, we have created the Gang Green dead center tabs using our battle tested firm but FLEXIBLE material. This allows the engineered flex to do it's job at an even higher level of effectiveness.

They can be pulled with a slide hammer or mini lifter, but start slow! You'll be surprised how well they can pull the center of the damage.

Length: 24" (60.9cm)
Diameter: 1/2" (1.27cm)
Includes: R4 tip

1/2” diameter double bend rod that accepts all the interchangeable tips we manufacture.

The pipe handle is perpendicular to the bends and threaded to accommodate one or two handle extensions, for added leverage.

The overall length of the bends is 4 inches (with a tip) and the combined angle is 80 degrees.

Note: A recommended use of the RDI24 would be to stack a combination of E1, E2, and E3 Extension Tips for putting your desired tip closer to the dent when leveraging off a front tire on fenders. This will also allow your hand to keep from hitting the tire when working.

The minimum essential PDR Tools for fixing dents on hail damage prone areas.

Brace Tools for for inside of braces on the hood and trunk.

• 3 of our most popular whale tails
• 2 rods
  • 1 x Single Bend 36'' (90cm) with a tapered teardrop design
  • 1 x  Double Bend Interchangeable tip hail rod
• 2 x Extensions for the hail rod
• 1 x wire twisting tool
• 1 x hand tool 3''
• 1 x s hook fulcrum

Dent Reaper Dead Center Hex Tabs combine the amazing Dead Center Technology developed by Keco with a design twist from Jon Videen at Dent Reaper. The stepped tab face increases the strength in the center of the tab while providing extra adhesion power and flex at the tab edges.

• Patented Dead Center Technology - the specialized neck to face ratio provides the best possible rigid center pull with flex along the edges to avoid overpulling
• Hexagonal Tab Shape - extreme strength and rigidity, perfect for pulling on panel edges and prevents unused tabs from rolling
• Stepped Tab Thickness - increases force at the center of the pull while increasing adhesion with a larger total surface area
• KECO Ice Material - extremely strong and rigid formula.