Glexo Hail Micro Kit – 6 tabs
    Glexo Hail Micro Kit – 6 tabs
    Glexo Hail Micro Kit – 6 tabs
    Glexo Hail Micro Kit – 6 tabs
    Glexo Hail Micro Kit – 6 tabs
  • Out-of-Stock

Glexo Hail Micro Kit – 6 tabs

R7,210.50
VAT excluded

The Glexo Hail Micro Kit has been specially designed to help technicians with small hail damages. Repairing hail is a difficult job where saving time is very important. Since the Glexo PDR cold glue can overheat during continuous operation, affecting its performance, the Glexo Hail Micro system includes redundant tabs to enable continuous working. The kit includes a fundamentally new PDR cold glue composition with very high adhesive properties, which allows you to perform repairs with insignificant contact areas.

The Glexo Hail Micro kit includes two tabs 10mm /0,39”, two tabs 15mm /0,59” and two tabs 20mm /0,79". The kit contains two types of PDR cold glue composition for different working conditions.

Quantity
Add to wishlist
Out-of-Stock

  Security policy

Your details is secure with us

  Delivery policy

Free delivery above R10K

  Customer Service

We guarantee great customer service

The Glexo Hail Micro Kit has been specially designed to help technicians with small hail damages. Repairing hail is a difficult job where saving time is very important. Since the Glexo PDR cold glue can overheat during continuous operation, affecting its performance, the Glexo Hail Micro system includes redundant tabs to enable continuous working. The kit includes a fundamentally new PDR cold glue composition with very high adhesive properties, which allows you to perform repairs with insignificant contact areas.

All tabs are equipped with Glexo's patented proprietary locking system with O-ring for quick and secure installation. Can be used and are suitable for use with arbitrary slide hammer. The recommended weight of the slide hammer is 0.8-1kg / 1.7-2.2lb.

The kit is equipped with a fundamentally new PDR cold glue with increased adhesion, which allows you to increase productivity when repairing hail damage.

The technique of work includes the following stages:

  1. Prepare work surface. The working surface must be free of dirt and grease. For guaranteed high adhesion it is recommended to use the Glexo Surface Preparation System (SPS).
  2. Install the Glexo Hail Micro tab with applied PDR cold glue on the slide hammer until it stops.
  3. Using a twisting motion, glue the tab to the center of the damage. Use a slide hammer as a lever.
  4. Remove damage with a sharp hammer blow. Repeat if necessary.

The Glexo Hail Micro kit includes two tabs 10mm /0,39”, two tabs 15mm /0,59” and two tabs 20mm /0,79". The kit contains two types of PDR cold glue composition for different working conditions.

After work, the PDR tabs are stored directly with the applied adhesive in the wooden box in which the system is supplied. To prevent sticking, anti-adhesive films are included in the kit, which must be wrapped around the PDR tabs with the applied composition.

The Glexo Hail Micro kit comes with a 1 year warranty.

GLX-MICRO

8 other products in the same category:

Starter Set - Hail

R13,765.50
Availability: 4 In Stock

The minimum essential PDR Tools for fixing dents on hail damage prone areas.

Brace Tools for for inside of braces on the hood and trunk.

  • 3 of our most popular whale tails
  • 2 rods
    • 1 x Single Bend 36'' (90cm) with a tapered teardrop design
    • 1 x  Double Bend Interchangeable tip hail rod
  • 2 x Extensions for the hail rod
  • 1 x wire twisting tool
  • 1 x hand tool 3''
  • 1 x s hook fulcrum

6pc Brace Tool Set

R3,496.00
Availability: 3 In Stock

6 PIECES IN THIS SET

  • 14" Brace Tool Right- BR14
  • 18" Brace Tool Right- BR18
  • 24" Brace Tool Right- BR24
  • 14" Brace Tool Left - BL14
  • 18" Brace Tool Left- BL18
  • 24" Brace Tool Left- BL24

These are the (3) largest left and right brace tools.

10dg bend angle moved well back from the working tip to maximise reach

Handle rotated 12dg to improve ergonomics.

Diameter :to: length ratio just right for the power needed.

For hail damage these are a must have for every dent tech.

Brace Tools are made from special high carbon spring steel.

Centipede® Variety Pack Rigid Crease Glue Tabs...

R4,696.58
Availability: 8 In Stock

The KECO Centipede Crease tabs are a highly versatile glue tab that permits the technician to work large dent in small increments. Techs have the ability to carefully pull stubborn creases within peaks and valleys created by lines of smaller crease or hail tabs and deep dents.

Available adapters allow Centipedes to be pulled with the KECO K-Bar®, K-Beam®, K-Beam Jr.®, industry standard slide hammers, mini-lifters, and even a rope ratchet and chains.

  • Blue Material - solid pull and vibration absorbing hold
  • Rigid Spine - increased strength for deep dents
  • Smooth Face - strongest possible pull and hold
  • Includes -
    • 12.5 x 54 mm
    • 25 x 105 mm
    • 12.5 x 156 mm
    • 25 x 54 mm
    • 25 x 105 mm
    • 25 x 156 mm
    • 38 x 156 mm
    • 50 x 156 mm
    • 50 x 54 mm
    • 38 x 54 mm
    • 50 x 105 mm
    • 38 x 105 mm

Gang Green Dead Center® 11 mm Round Glue Tabs...

R654.41
Availability: 23 In Stock

Gang Green Dead Center Tabs are the new kings for Hail Repair!

The dead center tabs have shown us that the most effective way to move metal is to flex with the metal as the repair is performed.

Using that knowledge, we have created the Gang Green dead center tabs using our battle tested firm but FLEXIBLE material. This allows the engineered flex to do it's job at an even higher level of effectiveness.

They can be pulled with a slide hammer or mini lifter, but start slow! You'll be surprised how well they can pull the center of the damage.

This website uses cookies to ensure you get the best experience on our website