There are 189 products.
· ISO metric M8 thread NOT compatible with interchangeable tip push rods
· 2x Stainless steel knockdowns with magnetic ends to prevent rolling
· 12x Steel interchangeable knockdown tips
· 16x Black-plastic interchangeable tips
· 4x Root beer-plastic interchangeable tips
Adhesive composition (PDR cold glue) Glexo for high application temperatures, above 86°F /30°C. Uncompromising performance in any job in hot conditions. Under standard temperature conditions, the composition will appear solid, and its adhesive properties will appear in hot weather.
The adhesive composition is intended for use with Glexo metal PDR tabs, but it can also be applied separately using special techniques. A feature of the composition is its pronounced non-Newtonian behavior. So with a sharp application of force, the cold glue becomes much harder, allowing the maximum force from the tool to be transferred to the repaired surface. The remains of the composition are removed from the surface with the bulk on the tab.
Adhesive composition (PDR cold glue) Glexo is perfect for normal application temperatures below 86°F/30°C. It promises unwavering performance across all tasks and conditions.
This PDR cold glue is designed for use with Glexo metal PDR tabs, but it can also be applied separately using specific techniques. A key characteristic of this glue is its significant non-Newtonian behavior. In other words, when you apply a quick force, the glue becomes much harder, allowing the maximum power from the PDR tool to be transferred to the surface being repaired. The leftover glue is then removed from the surface along with the majority on the tab. If you need to detach the PDR cold glue from the surface that's being fixed, you should avoid sudden movements and separate it smoothly.
Complete Dead Center Set (GGDCVP56)
This will get you TWO of EVERY tab size we make in the Gang Green Dead Center model line up.
10 Round sizes, and 18 Crease tabs! You'll be ready for any and everything that comes your way as a tech.
Gang Green Dead Center tabs are all about engineered flex and allowing the tab to move WITH the metal to get the repair you dream about: Easy clean pulls with minimal effort and MAXIMUM effectiveness.
The KECO Centipede Crease tabs are a highly versatile glue tab that permits the technician to work large dent in small increments. Techs have the ability to carefully pull stubborn creases within peaks and valleys created by lines of smaller crease or hail tabs. The articulated design of the Centipede permits flexibility to match gentle contours or adhere to deep dents.
Available adapters allow Centipedes to be pulled with the KECO K-Bar®, K-Beam®, K-Beam Jr.®, industry standard slide hammers, mini-lifters, and even a rope ratchet and chains.
Dead Center® Crease Tabs.
Dead Center® Finishing Tabs.
When we saw this door jammer a few years ago it really impressed us. We think it's one of the best door jammers available for paintless dent repair. So we contacted the maker and now offer it for sale.
We think you'll really enjoy using it.
Pack of 100 Soft Tips.
These tips first the S4 Tip
Dentcraft H-Blending Polished Tip Set
Mushroom Tip w/ Soft Blue PVC 64/16" (4") Working Diameter
4" Blue Aluminum Knock Down w/ B4-P Tip
3" Blue Aluminum Knock Down w/ B4-P Tip
Length: 48" / 1.2m
Diameter: .243" / 6.2mm
Bend angle: 70
Double Bend Rod
Diameter: 7/16" (1.1 cm)
Length: 24" (60.9 cm)
Single Bend length: 5/16" (7.9mm)
Diameter: 22" (55.8cm)
Length: 36" (91.4cm)
Diameter: 5/8" (1.58cm)
Includes: R4 and H24 tip
30” interchangeable tip rod including R4 Tip
24” interchangeable tip rod including R4 Tip
Length: 36" (91.4cm)
Diameter: 1/2" (1.27cm)
Includes: R4 tip
Length: 24" (60.9cm)
Diameter: 1/2" (1.27cm)
Includes: R4 tip
1/2” diameter double bend rod that accepts all the interchangeable tips we manufacture.
The pipe handle is perpendicular to the bends and threaded to accommodate one or two handle extensions, for added leverage.
The overall length of the bends is 4 inches (with a tip) and the combined angle is 80 degrees.
Note: A recommended use of the RDI24 would be to stack a combination of E1, E2, and E3 Extension Tips for putting your desired tip closer to the dent when leveraging off a front tire on fenders. This will also allow your hand to keep from hitting the tire when working.
Long Flag Diameter: .306 (5/16) / 7.94 mm
Length: 24" / 60.9cm
Flag: 6" / 15.2cm
Length: 24" / 60.96cm OAL
Diameter: .306" / 7.7mm
Other: -Tip is 4.75” (12.1cm) from shaft
Tip is 16.75” (42.5cm) from handle
Sharp Side Panel Hook 5
Flag: 3''
Diameter: 5/16'
Length: 24''
Length: 10”/ 25.4cm
Thickness of Shaft: .125" / 3.175mm
Width of shaft: .250”/ 6.350mm
Tip width: 1/2”/ 1.270cm
Length: 24" / 60.9cm
Thickness of Shaft: .190" / 4.826mm
Width of shaft: .312”/ 7.92mm
Tip width: 1-1/8”/ 2.8cm
This set Includes (4) Picks:
· 14oz enough for comfortable all-day use but powerful enough to pull medium to large hail dents
· Specially designed head works with your favourite standard sized hail tabs
· Designed with comfort in mind, the ergonomic handle allows for precise an straight pulls
· Includes free tabs
· ISO metric M8 thread NOT compatible with interchangeable tip push rods
· Blending Hammer - Carbon Fiber Shaft.
· Includes a root beer and hard plastic Tips
· Removable plastic ball.
The rectangular tab for PDR cold glue Glexo v2 has a size of 76x30mm /3"x1.2" and is used in PDR to work with Glexo cold glue. The tab is made of high-strength stainless steel, has a great appearance and high reliability. The working surface is polished to improve the adhesion of cold PDR glue, which eliminates its separation from the tab during operation.
The tab is equipped with a patented proprietary quick fastening system with an O-ring for reliable and quick fixation. Fastening to the slide hammer is simple and intuitive, it is carried out by twisting movements after inserting the asymmetric nut of the tab into the seat of the slide hammer.
The small round tab for PDR cold glue Glexo v2 has a diameter of 35mm/ 1.38" and is used in PDR to work with Glexo cold glue. The tab is made of high-strength stainless steel, has a great appearance and high reliability. The working surface is polished to improve the adhesion of PDR cold glue, which eliminates its separation from the tab during operation. The tab is equipped with a patented proprietary quick fastening system with an O-ring for reliable and quick fixation. Fastening to the slide hammer is simple and intuitive, it is carried out by twisting movements after inserting the asymmetric nut of the tab into the seat of the slide hammer.
